FOR SALE 1970 VW Squareback

Hate to see the 'Fat Chick' leave, but it's beyond my resources to keep up with this lady. Hopefully I can find a new owner who can give her the time and attention she needs.

Just had her tuned up at VW Paradise and had the hood release cable repaired (which had snapped!).

Here's the last few pics that include headlights re-installed, interior panels re-installed, plus new powder coated rims and new hubcaps:

Slow Ride (Take it Easy)!

Wifey let me spend the weekend in the garage doing work on the Squareback (Thanks, Wifey!).



I installed both vent flaps (ventilation windows on the doors), charged the battery, and started the engine. The engine was a bit hesitant, but after a few tries it finally turned over and ran like a top.

I put it in gear and drove a few 'victory laps' around the block:

http://www.youtube.com/watch?v=dAAzs2DzJVE



By the way, this is what your garage floor looks like when you have not driven the car for over a year...

Pop-out windows re-sealed

I replaced the rubber seals (glass-to-frame and frame-to-body) this weekend on the pop-out windows.
Here's a 'before' shot of the pop-out window. Note the rotten rubber between the frame and glass. The outer seal was even worse- it chipped off easily with a screwdriver.

The screws holding the frames together were rusted shut and I needed to use ez-outs to remove them. Here is a frame disassembled:
Once the machine screws finally came loose. I polished the frames using aluminum wheel polish and some elbow grease. Some of the film/pitting came off, but not all. Could not find any brasso anywhere to try :(

I ordered replacement screws for about $6 from McMaster-Carr.


New rubber from West Coast Metric is installed, and the window is back in place. Only the driver and passenger doors to go!

VolksWeekend 08 August

It's been a while. With wife and sons out of town this weekend, I had a chance to spend time in the garage and knock out some VW projects. I finished fender beading on the front and rear passenger fenders and installed the gaskets on the rear hatch and forward trunk.


Rear hatch, before new gasket.


Rear hatch, after gasket, passenger fender beading, re-installed tail lights.

Front hatch before new gasket.

Front hatch after new gasket.

Front of the car, new fender beading on pax side. Finally got enough junk out of the trunk to close the lid!

New windshield

I finally got a new windshield installed. Now I can drive around without using ski goggles!





~ $236 from All Star Glass.

Still waiting for gaskets for the side pop-out windows...

Driver's rear fender

Today I re-installed the driver's side rear fender, including replacement engine air intake seal and black fender beading.

The engine intake seal (black rubber gasket beneath window) was $28 per pair from ISP west.

Here's the fender installed, with black fender bead (gasket) along the seam.

Tomorrow should be new windshield time!

Rear Windows, 12/26/08

My dad stopped by today to help re-install some of the glass. Could not do it with just myself and my 9-year-old son... needed some extra oomph! For those who have not tried this before, it takes a lot of silicone spray combined with a ton of pushing and shoving.



The black strips in the photo are electrical tape I used to hold the headliner (interior vinyl) in place. That's 3 windows down, 5 to go!

The Fat Lady Sings!

Ok, I found out that this body style of VW Squareback is called a 'fat chick' due to the larger trunk/'snout'. Could not resist using this in the title. Here are the photos straight out of the Escondido MAACO paint shop (windows still removed).


MAACO said they would re-touch this area on the gas lid for free. Otherwise no complaints for the $1500 they charged me.

10/13 Off to MAACO

I had a local shop quote me over $4k to sand and paint the vehicle. This included $1200 in materials (!).

I want to drive this thing before gas gets to be $10 a gallon and asked them for a referral. They said the local MAACO in Escondido should be able to do a serviceable job for under $2k. They quoted me around $1500 to do some sanding, prep, and re-paint the factory color. We'll see how it goes.

Not having a windshield installed made it a bit challenging to drive 6 miles to the local shop. Ski goggles came in handy!

Here's the 'before' shots of the condition of the squareback before drop-off:




Dig the plate?

10/11 Golden (Bondo) Shower

OK it's been a while... I went out of action in mid-March for shoulder surgery, adopted a baby in May, and was out of the country from mid-June through mid-July. Long story short, I'm back in action, and back to getting this thing ready for paint. There's lots of POR-15 in the window sills, covered up with some primer.

I wonder, of the old VW's still in existence, how much steel is remaining and how much POR-15 has taken place of the metal?

Did some more bondo/sanding work on the car to get it ready for paint. Here are the shots:


Before - Note the dings. I ground down a few inches of cracked bondo and then filled in w/Lead filler.




After. I used mostly lead filler with a 'skim coat' :) of bondo over it.
Here's the dreaded welded-in patch. After a full weekend of sanding and build-up, you can hardly tell the difference between the original and replacement piece.

Here's the area beneath the passenger headlight. Nice and smooth!

Passenger door and rear quarter panel... good to go!

5/10 Yet more fun w/ MIG Welder (Tool Time)

Using 1 1/2 inch x 1/8 inch steel L-bracket, I welded together a Type 3 generator belt wrench to hold the 24mm pulley nut, just like the one in the John Muir "How to keep your Volkswagen Alive" book.

This is more how I was expecting the welder to work in the first place. Much better. Now All I have to do is cut the 24mm groove in the short end. I'll do this @ work, where we have some s-weet tools in the 'mechanical assembly area'.

5/10 More fun w/ MIG welder (Passenger Front Fender)

A bit more proficient w/ the welder after the first few passes (btw, I DID practice on some scrap metal first). Still burns the fender sheet metal like tin foil. Heres the spot below the headlight and the spot right behind the wheel:

5/10 Fun with MIG Welders

Here are some shots of welding I did with the Home Depot Lincoln Electric HD100 flux-core MIG welder. The infernal bugger burns through sheet metal like it's tin foil.

I had better luck making a tool out of 1/8 inch steel L-bracket (next post).

Maybe I should use one with the inert gas upgrade next time? Does the gas cool the area so you don't get so much burn-through?

Here's the driver side Rear Quarter:



I think I'll fill in the holes with some Metal Glue on a caulking gun, then cover w/filler/polyester. What a mess! At least I didn't start a fire!

Here's the inside. I welded a strip of 40 mil sheet metal to fill in the gap for rigidity:
I'll grind it down some more. This is going to be covered w/ contact paper anyways, so it does not have to be too pretty, just smooth. Also will fill in the gaps w/ metal glue.

Steel Wheels 3/01

Purchased recycles wheels from the scrap yard for $65 and had them powder coated at San Diego's RW Little for $225. Not bad Eh?

I could grate cheese with this!

Ok, the windows are all removed, and I've started grinding down to bare metal in some suspect spots.


On advice of a Samba forum post, I took a closer look beneath the headlights. The driver's side is fine, but the passenger side had a tiny discoloration (sorry, no 'before' photo) about the size on a pinhead. Here's what the 2x3 inch area looked like after hitting it with the wire wheel...





Here's an area behind the wheel on the passenger's side. It also started out as a small blister before the wire wheel... now its an opening about the size of a golf ball.
I got some 40-mil aircraft-grade '4130' sheet metal from McMaster-Carr for about $38. The cost also includes angle iron I will use to make a Type III pulley wrench (from the Muir Book) and shipping.

Peeling the Onion

I purchased new window rubber for all side and rear windows from JBugs/California Pacific. Also got a new gas cap, since the old one was a locking type from WalMart and looked a bit ghetto ($228 total for the replacement rubber and gas cap). They were out of windshield rubber, so I will have to go back next week and get some.

Upon closer inspection...

After removing the window rubber, it looks like the rust beneath this rear quarter is a bit more extensive. This may require welding a 'donor piece', which is certainly more than I bargained for when I bought the car.

There is a hump in the driver's side floor pan. Don't know if this is from a wreck or if someone used the wrong jacking location at some point. May require floor pan replacement.

Battery pan rusted through. This is a common trouble spot, and at least new replacement battery pans are available. Guess I'll have to learn welding.